Firmware

Unzip the archive file and follow the firmware update procedure. This firmware package is designed for the OSD Module.

[Warning]
Do not use this firmware with any other hardware as it may render your product unusable.
Do not unplug the USB cable during the upgrade process.
Always remove the OSD module safely via your operation system before unplugging the cable. Otherwise the OSD module may be damaged.

[Firmware Update Procedure]

1. Unzip downloaded file to extract the “firmware.bin” file.
2. Make sure the OSD module is turned off by switching the ON OFF switch to OFF position.
3. Press and hold the FN button while connecting the OSD to a personal computer (PC) using the microUSB cable. No LED will light up.
4. Keep the FN button pressed until a new drive is shown on your computer.
5. Browse the drive, there is one “.bin” file only.
6. Delete the original “.bin” file.
7. Copy the newly downloaded “firmware.bin” file into the drive. Do not use the replace file function to update the file. Delete the old file first, then copy the new file into the drive.
8. Safely remove the device via your operating system before unplugging the cable.
9. Power on the OSD module again to take effect.

[0.22 Changes] 2013/01/30
- Added: Flight time display on connected video receiver. Setup via RC Logger Commander Software.

Unzip the archive file and follow the firmware update procedure. This firmware package has been designed for the RC Logger PRO.

[Warning]
Do not use this firmware with any other hardware as it may render your product unusable. Do not interrupt the update process since this may render the RC Logger PRO unusable.

[Firmware Update Procedure]

1. Unzip download file and prepare firmware by renaming unzipped file to rclpro.bin.
   Copy the renamed file in the root directory of a SD card.
2. Make sure the RC Logger PRO is switched off.
3. Insert the SD card into the RC Logger PRO.
4. Press and hold the shutter button and switch the “Off / Camera mode / Video mode switch" to either video or camera position.
5. All three LED’s will blink in blue while the upgrade is processing. If no valid firmware file is detected all three LED’s will blink red.
6. After the upgrade is finished successfully the RC Logger PRO will turn off.
7. Turn off/on the RC Logger PRO.

[0.1.86 Changes] 2012/10/03
- Bugfix: Fixed recording terminated when using external supply.
- New: Relocate preview OSD on TV under PAL and NTSC (only for PRO version).

[0.1.83 Changes] 2012/07/17
- Bugfix: A/V black-out problem when using external supply.
- Bugfix: Blue image when using external power supply.
- Bugfix: Occassional black TV screen while leaving A/V Menu (PRO only using A/V Kit).

[0.1.82 Changes] 2012/06/21
- Bugfix: Sensor stops sending data during recording.

[0.1.81 Changes] 2012/05/15
- Added: LED indication for orientation setting:
        3-times blue flashing -> normal orientation
        3-times blue purple flashing -> 180 orientation
- Fixed: Debounce issue causing recording to start after releasing trigger button.

[0.1.80 Changes] 2012/04/29
- Added: New feature to change orientation by pressing and holding the shutter button for 5 seconds.

[0.1.79 Changes] 2012/04/24
- Added: Enable USB mass storage during power-up.

[0.1.78 Changes] 2012/03/30
- Added: Manual shutter speed selection (requires A/V Kit).
- Fixed: Corrected word length in UI (if using A/V Kit) for some languages.

[0.1.75 Changes] 2012/02/16
- Fixed black screen/lockup when exiting playback mode.

[0.1.74 Changes] 2012/01/27
- Support IMU orientation setting features.
- PWM trigger response improved.

[0.1.71 Changes] 2011/11/30
- Exif updated.

[0.1.70 Changes] 2011/11/16
- Photo AE setting improved.
- Fixed bug of FW version number display.

[0.1.65 Changes] 2011/10/08
- Auto white balance (purple/blue) further corrected.
- Exposure reduced by one step.
- Correct mapping video quality bit.

[0.1.63 Changes] 2011/09/16
- Auto white balance (purple/blue) corrected.

[0.1.61 Changes] 2011/09/07
- Reduce color shading.
- Correct bug in config.cfg.

[0.1.60 Changes] 2011/09/05
- Auto white balance adjustment; correct green/blue effect.
- Correct handling of byte 2048 in X2 module.

[0.1.58 Changes] 2011/09/02
- Auto white balance adjustment.
- 1st byte 0X00 address in X2 module corrected.

[0.1.56 Changes] 2011/08/29
- Correct auto white balance.
- Real time audio output in photo mode.
- Correct LED indication for FW upgrade.
- LED flashes once under singel photo mode.
- Default setting: PWM = disable.
- AWB default = "A".

[0.1.53 Changes] 2011/08/23
- Fix bug on date/time stamp.
- "D" set as default white balance.

[0.1.52 Changes] 2011/08/20
- External module disabled by default.
- 4 digit in sampling rate and time lapse interval.
- X2 module label changed to Z.
- Digit setting for video quality on PRO and HD2 matched.
- Correct format on header Switch between PRO and HD2.

[0.1.48 Changes] 2011/08/15
- Firmware for RC Logger PRO only.
- Post "first production batch" release.
- Minor adjustments.

[0.1.47 Changes] 2011/08/15
- Firmware for RC Logger PRO only.
- First production batch.
- Added: Red dot and timer for recording.
- Audio bypass disabled by default.

[0.1.46 Changes] 2011/08/12
- First release for RC Logger PRO only.

Unzip the archive file and follow the firmware update procedure. This firmware package has been designed for the RC Logger HD2.

[Warning]
Do not use this firmware with any other hardware as it may render your product unusable. Do not interrupt the update process since this may render the RC Logger HD2 unusable.

[Firmware Update Procedure]

1. Unzip download file and prepare firmware by renaming unzipped file to rclhd2.bin.
   Copy the renamed file in the root directory of a SD card.
2. Make sure the RC Logger HD2 is switched off.
3. Insert the SD card into the RC Logger HD2.
4. Press and hold the shutter button and switch the “Off / Camera mode / Video mode switch” to either video or camera position.
5. All three LED’s will blink in blue while the upgrade is processing. If no valid firmware file is detected all three LED’s will blink red.
6. After the upgrade is finished successfully the RC Logger HD2 will turn off.
7. Turn off/on the RC Logger HD2.

[0.1.86 Changes] 2012/10/03
- Bugfix: Fixed recording terminated when using external supply.

[0.1.83 Changes] 2012/07/17
- Bugfix: A/V black-out problem when using external supply.
- Bugfix: Blue image when using external power supply.
- Bugfix: Occassional black TV screen while leaving A/V Menu (PRO only using A/V Kit).

[0.1.82 Changes] 2012/06/21
- Bugfix: Sensor stops sending data during recording.

[0.1.81 Changes] 2012/05/15
- Added: LED indication for orientation setting:
        3-times blue flashing -> normal orientation
        3-times blue purple flashing -> 180 orientation
- Fixed: Debounce issue causing recording to start after releasing trigger button.

[0.1.80 Changes] 2012/04/29
- Added: New feature to change orientation by pressing and holding the shutter button for 5 seconds.
 
[0.1.79 Changes] 2012/04/24
- Added: Enable USB mass storage during power-up.

[0.1.75 Changes] 2012/02/16
- Fixed black screen/lockup when exiting playback mode.

[0.1.74 Changes] 2012/01/27
- Support IMU orientation setting features.
- PWM trigger response improved.

[0.1.71] Changes 2011/11/30
- Exif updated.
 
[0.1.70] Changes 2011/11/16
- Photo AE setting improved.
- Fixed bug of FW version number display.

[0.1.65 Changes] 2011/10/08
- Auto white balance (purple/blue) further corrected.
- Exposure reduced by one step.
- Correct mapping video quality bit.

[0.1.63 Changes] 2011/09/16
- Auto white balance (purple/blue) corrected.

[0.1.61 Changes] 2011/09/07
- Reduce color shading.
- Correct bug in config.cfg.

[0.1.60 Changes] 2011/09/05
- Auto white balance adjustment; correct green/blue effect.
- Correct handling of byte 2048 in X2 module.

[0.1.58 Changes] 2011/09/02
- Auto white balance adjustment.
- 1st byte 0X00 address in X2 module corrected.

[0.1.56 Changes] 2011/08/29
- Correct auto white balance.
- Real time audio output in photo mode.
- Correct LED indication for FW upgrade.
- LED flashes once under singel photo mode.
- Default setting: PWM = disable.
- AWB default = "A".

[0.1.53 Changes] 2011/08/23
- First release for RC Logger HD2.

Unzip the archive file and follow the firmware update procedure. This firmware package has been designed for the RC Logger HD.

[Warning]
Do not use this firmware with any other hardware as it may render your product unusable. Do not interrupt the update process since this may render the RC Logger HD unusable.

[Firmware Update Procedure]

1. Unzip/Unrar the firmware archive file and save it in the root directory of an empty SD card.
2. Make sure the logger is turned off.
3. Insert the prepared SD card into the RC Logger HD (see 1.).
4. Press and hold the shutter button "S" and switch the “Off / Video mode / Camera mode / switch” to either "photo"or "video" position.
5. Wait until the status LED goes off.
6. Turn off the logger.

[022 Changes] 2011/01/14
- First post production firmware update.
- Set correct LED status if recording stopped due to file size limitation.
- Media Data are now stored in separate folders.

Unzip the archive file and follow the firmware update procedure. This firmware package has been designed for the 2.4 GHz Data RX LCD Monitor.

[Warning]
Do not use this firmware with any other hardware as it may render your product unusable. Do not interrupt the update process since this may render the 2.4 GHz Data RX LCD Monitor unusable.

[Firmware Update Procedure]

1. Download the latest firmware update from “http://www.rclogger.com” to your personal computer. If its name is not “firmware.bin”, rename it.
2. Make sure the RX LCD monitor is turned off.
3. Insert the micro-USB plug of the cable into the micro-USB port on the RX LCD monitor.
4. Insert the USB plug of the cable into a vacant port of the personal computer.
5. Press and hold the button “>> / SET” and slide the power switch to “ON” position.
6. The device will be recognised as a mass storage device. A file “firmware.bin” will be found inside.
7. Delete the “firmware.bin” file.
8. Store the new firmware file in the same directory from which you have deleted the old file.
   
   NOTE: Replacing the file on the device with files other than the official firmware release may damage the device.
    
9. Safely remove the mass storage device from your computer.
10. Disconnect the RX LCD monitor and slide the power button “ON/OFF” to “OFF” position again. Turn it on again after a few  seconds and the new firmware version is shown on the device information page.

[0.07 Changes] 2012/03/10
- Added IMU Add-On Module Support.

[0.06 Changes] 2011/08/19
- Bug Fix - Display of [GPS Sensor - Speed].

Unzip the archive file and follow the firmware update procedure as explained in the RC Rogger LC operating instructions. This firmware package has been designed for the RC Logger LC.

Firmware update procedure:

Warning. Do not disconnect the connection to the computer during the update process. Otherwise, the files in the internal memory can be damaged and the entire update process must be repeated.

1. Make sure that the product is switched off.
2. Press and hold down the “Trigger” button on the product.
3. Connect the product to a computer via the USB cable. The product is detected as an external device.
4. Release the “Trigger” button.
5. Delete the “firmware.bin” file.
6. Store the new firmware file in the same directory from which you have deleted the old file.
7. Separate the product fully first via the operating system, and then by the USB cable.

Release notes:

[RC Logger LC Firmware V1.1] 2012/01/21:
- Added: Support IMU data and setting.
- Added: Increase to 4s delay after power on the LC to provide support for IMU.
- Updated: USB device name updated to “RC Logger LC” (within device manager).